Distortional buckling in monosymmetric I-beams: Reverse-curvature bending: Fid-Bau Portal

Fachinformationsdienst BAUdigital

Eine Plattform für die Wissenschaft: Bauingenieurwesen, Architektur und Urbanistik

Distortional buckling in monosymmetric I-beams: Reverse-curvature bending

Kumar, Ashwini / Samanta, Avik

AbstractThis paper deals with distortional buckling in monosymmetric propped cantilever I-beams under two types of load: a central point load and a uniformly distributed load. Top-flange and bottom-flange load positions are considered. ABAQUS is used for the investigation. Moment modification factors are obtained and are compared with those based on Structural Stability Research Council Guidelines, which take into account lateral–torsion buckling only. It is seen that provisions in SSRC Guidelines seriously overestimate the critical load, especially for short beams.

Zugriff

Zugriff prüfen

Verfügbarkeit in meiner Bibliothek prüfen

Bestellung bei Subito €

Seitennavigation

Dokumentinformationen

Ähnliche Titel

Exportieren, teilen und zitieren

Distortional buckling in monosymmetric I-beams: Reverse-curvature bending

Kumar, Ashwini / Samanta, Avik

AbstractThis paper deals with distortional buckling in monosymmetric propped cantilever I-beams under two types of load: a central point load and a uniformly distributed load. Top-flange and bottom-flange load positions are considered. ABAQUS is used for the investigation. Moment modification factors are obtained and are compared with those based on Structural Stability Research Council Guidelines, which take into account lateral–torsion buckling only. It is seen that provisions in SSRC Guidelines seriously overestimate the critical load, especially for short beams.

Distortional buckling in monosymmetric I-beams: Reverse-curvature bending

Kumar, Ashwini / Samanta, Avik

AbstractThis paper deals with distortional buckling in monosymmetric propped cantilever I-beams under two types of load: a central point load and a uniformly distributed load. Top-flange and bottom-flange load positions are considered. ABAQUS is used for the investigation. Moment modification factors are obtained and are compared with those based on Structural Stability Research Council Guidelines, which take into account lateral–torsion buckling only. It is seen that provisions in SSRC Guidelines seriously overestimate the critical load, especially for short beams.

Zugriff

Zugriff prüfen

Verfügbarkeit in meiner Bibliothek prüfen

Bestellung bei Subito €

Seitennavigation

Dokumentinformationen

Ähnliche Titel

Exportieren, teilen und zitieren

Dokumentinformationen

Titel:

Distortional buckling in monosymmetric I-beams: Reverse-curvature bending

Beteiligte:

Kumar, Ashwini (Autor:in) / Samanta, Avik (Autor:in)

Erschienen in:

Thin-Walled Structures ; 44 ; 721-725

Erscheinungsdatum:

01.08.2006

Format / Umfang:

5 pages

ISSN:

DOI:

https://doi.org/10.1016/j.tws.2006.08.003

Medientyp:

Aufsatz (Zeitschrift)

Format:

Elektronische Ressource

Sprache:

Englisch

Schlagwörter:

Buckling , Distortion , Cantilever

Ähnliche Titel

Distortional buckling in monosymmetric I-beams: Reverse-curvature bending

Kumar, Ashwini | Online Contents | 2006

Distortional buckling in monosymmetric I-beams

Samanta, Avik | Online Contents | 2006

Distortional buckling in monosymmetric I-beams

Samanta, Avik / Kumar, Ashwini | Elsevier | 2005

Distortional buckling of monosymmetric I-beams

Bradford, Mark A. | Elsevier | 1985

Distortional buckling of monosymmetric I-beams

Bradford, Mark A. | TIBKAT | 1984