A platform for research: civil engineering, architecture and urbanism
A platform for research: civil engineering, architecture and urbanism
On the role of finite grid extent in SOLPS-ITER edge plasma simulations for JET H-mode discharges with metallic wall
The impact of the finite grid size in SOLPS-ITER edge plasma simulations is assessed for JET H-mode discharges with a metal wall. For a semi-horizontal divertor configuration it is shown that the separatrix density is at least 30% higher when a narrow scrape-off layer (SOL) grid width is chosen in SOLPS-ITER compared to the case for which the SOL grid width is maximised. The density increase is caused by kinetic neutrals being not confined inside the divertor region because of the reduced extent of the plasma grid. In this case, an enhanced level of reflections of energetic neutrals at the low-field side (LFS) metal divertor wall is observed. This leads to a shift of the ionisation source further upstream which must be accounted for as a numerical artefact. An overestimate in the cooling at the divertor entrance is observed in this case, identified by a reduced heat flux decay parameters λqdiv. Otherwise and further upstream the mid-plane heat decay length λq parameter is not affected by any change in divertor dissipation. This confirms the assumptions made for the ITER divertor design studies, i.e. that λq upstream is essentially set by the assumptions for the ratio radial to parallel heat conductivity. It is also shown that even for attached conditions the decay length relations λne > λTe > λq hold in the near-SOL upstream. Thus for interpretative edge plasma simulations one must take the (experimental) value of λne into account, rather than λq, as the former actually defines the required minimum upstream SOL grid extent. Keywords: edge plasma, modelling, SOLPS-ITER, JET, divertor
On the role of finite grid extent in SOLPS-ITER edge plasma simulations for JET H-mode discharges with metallic wall
The impact of the finite grid size in SOLPS-ITER edge plasma simulations is assessed for JET H-mode discharges with a metal wall. For a semi-horizontal divertor configuration it is shown that the separatrix density is at least 30% higher when a narrow scrape-off layer (SOL) grid width is chosen in SOLPS-ITER compared to the case for which the SOL grid width is maximised. The density increase is caused by kinetic neutrals being not confined inside the divertor region because of the reduced extent of the plasma grid. In this case, an enhanced level of reflections of energetic neutrals at the low-field side (LFS) metal divertor wall is observed. This leads to a shift of the ionisation source further upstream which must be accounted for as a numerical artefact. An overestimate in the cooling at the divertor entrance is observed in this case, identified by a reduced heat flux decay parameters λqdiv. Otherwise and further upstream the mid-plane heat decay length λq parameter is not affected by any change in divertor dissipation. This confirms the assumptions made for the ITER divertor design studies, i.e. that λq upstream is essentially set by the assumptions for the ratio radial to parallel heat conductivity. It is also shown that even for attached conditions the decay length relations λne > λTe > λq hold in the near-SOL upstream. Thus for interpretative edge plasma simulations one must take the (experimental) value of λne into account, rather than λq, as the former actually defines the required minimum upstream SOL grid extent. Keywords: edge plasma, modelling, SOLPS-ITER, JET, divertor
On the role of finite grid extent in SOLPS-ITER edge plasma simulations for JET H-mode discharges with metallic wall
S. Wiesen (author) / S. Brezinsek (author) / X. Bonnin (author) / E. Delabie (author) / L. Frassinetti (author) / M. Groth (author) / C. Guillemaut (author) / J. Harrison (author) / D. Harting (author) / S. Henderson (author)
2018
Article (Journal)
Electronic Resource
Unknown
Metadata by DOAJ is licensed under CC BY-SA 1.0
A spatially hybrid fluid-kinetic neutral model for SOLPS-ITER plasma edge simulations
| DOAJ | 2019
SOLPS-ITER simulations of the ITER divertor with improved plasma-facing component geometry
| Elsevier | 2025
SOLPS-ITER modeling of Ar and N seeded discharges in ASDEX upgrade and ITER
| DOAJ | 2023