A platform for research: civil engineering, architecture and urbanism
A platform for research: civil engineering, architecture and urbanism
Effect of industrial flare DREs derived by CFD and WERF on ozone pollution through CAMx simulation
Abstract Flare is the last safety measure for daily operations in oil, gas & chemical process industries (OGCPI). However, an excessive flaring releases large quantity of emissions of VOCs and NOx, which may suddenly enhance local ozone as a secondary pollution. Normally, the flare destruction and removal efficiency (DRE) of 98% or 99% is regulated as the national standard and presumed for industrial practices in the U.S. Unfortunately, real DRE values could be much lower than the standard due to impact factors including various meteorological and operating conditions such as the cross-wind speed, flare jet velocity and heating value of combustion. Thus, it is critically important to explore the sensitivity of the regional ozone impact due to low DREs of OGCPI flare combustions. In this paper, a systematic methodology has been developed to examine ozone impacts due to the low flare DREs, which have never been systematically studied before. The DRE formulas were derived from computational fluid dynamic (CFD) modeling and Water Environment Research Foundation (WERF) results and then employed to recompile the point source emission inventory. After that, comprehensive air quality model with extensions (CAMx) was employede to simulate and quantify local ozone changes impacted by flare emissions of OGCPI. Case studies indicate that the maximum hourly ozone increments due to the low DRE through CFD and WERF modeling is 0.18 ppb and 1.3 ppb, respectively. This study could enrich fundamental understandings of industrial point source emissions and provide the quantitative and valuable support for the ozone pollution caused by OGCPI flare emissions under low DRE instead of standard values.
Graphical abstract Display Omitted
Highlights Coupling Dynamic Flaring DREs with CAMx Modeling for Ozone Simulation. Flare DRE corrections established based on both CFD and WERF modeling. Effect of Flare DRE on Regional Ozone Pollution from OGCPI.
Effect of industrial flare DREs derived by CFD and WERF on ozone pollution through CAMx simulation
Abstract Flare is the last safety measure for daily operations in oil, gas & chemical process industries (OGCPI). However, an excessive flaring releases large quantity of emissions of VOCs and NOx, which may suddenly enhance local ozone as a secondary pollution. Normally, the flare destruction and removal efficiency (DRE) of 98% or 99% is regulated as the national standard and presumed for industrial practices in the U.S. Unfortunately, real DRE values could be much lower than the standard due to impact factors including various meteorological and operating conditions such as the cross-wind speed, flare jet velocity and heating value of combustion. Thus, it is critically important to explore the sensitivity of the regional ozone impact due to low DREs of OGCPI flare combustions. In this paper, a systematic methodology has been developed to examine ozone impacts due to the low flare DREs, which have never been systematically studied before. The DRE formulas were derived from computational fluid dynamic (CFD) modeling and Water Environment Research Foundation (WERF) results and then employed to recompile the point source emission inventory. After that, comprehensive air quality model with extensions (CAMx) was employede to simulate and quantify local ozone changes impacted by flare emissions of OGCPI. Case studies indicate that the maximum hourly ozone increments due to the low DRE through CFD and WERF modeling is 0.18 ppb and 1.3 ppb, respectively. This study could enrich fundamental understandings of industrial point source emissions and provide the quantitative and valuable support for the ozone pollution caused by OGCPI flare emissions under low DRE instead of standard values.
Graphical abstract Display Omitted
Highlights Coupling Dynamic Flaring DREs with CAMx Modeling for Ozone Simulation. Flare DRE corrections established based on both CFD and WERF modeling. Effect of Flare DRE on Regional Ozone Pollution from OGCPI.
Effect of industrial flare DREs derived by CFD and WERF on ozone pollution through CAMx simulation
Ge, Sijie (author) / Wang, Sujing (author) / Xu, Qiang (author) / Ho, Thomas (author)
Atmospheric Environment ; 238
2020-06-20
Article (Journal)
Electronic Resource
English
Ozone pollution , Industrial emissions , Flare , DRE , CAMx
Wiley | 1992
| British Library Online Contents | 2016
WERF: Winter Diffuse Pollution in Urban Watersheds Affected by Deicing Operations
| British Library Conference Proceedings | 1998